Project Description

  • cage mill
  • cage mill
  • cage mill

Cage Mill

This machine is a medium-sized horizontal cage mill. Cage mill can crush a variety of single fertilizers with water content below 40%. Zhengzhou Fusmar Machinery is a professional fertilizer crushing machine manufacturer.

Whatsapp:+8615838279423

Email: info@fusmarmachinery.com

Send Inquiry

This machine is a medium-sized horizontal cage mill. Zhengzhou Fusmar Machinery is a professional fertilizer crushing machine manufacturer, this article will introduce this machine in detail.

Cage Mill Introduction

Cage mill can crush a variety of single fertilizers with water content below 40%, especially for materials with higher hardness. The machine designed according to the principle of impact crushing. The inner and outer sets of cages rotate at high speed and the material crushed through the impact of cage strips from inside to outside. It has a simple structure, high crushing efficiency, good sealing performance, stable operation, easy operation, and so on.

cage mill

Use And Characteristics Of The Cage Mill

The machine consists of main components such as the frame, the casing, the wheel set, and the two motors. During operation, one motor drives the large cage to rotate in the forward direction, and then the other motor drives the small cage to rotate in the opposite direction. The material enters the inner wheel frame through the hopper, and then the steel bar repeatedly crushes the material to achieve the effect of crushing the material.

The Main Technical Parameters

parameters data

Use Method Of The Machine

Before use, the fertilizer crusher placed on a certain position in the workshop. It can use without the equipment foundation,  connecting it to the power supply can use. The fineness of the pulverization controlled through the spacing of the two rolls. The smaller the spacing, and then the finer the fineness, but the output is lower. On the other hand, the uniform crushing and the better the effect, the higher the output. The device can design to mobile according to the user’s requirements, the user can move the corresponding position when using. It is very convenient to remove when not needed.

fertilizer crushing machine

Routine Maintenance

  1. The crushermotor has been sealed before leaving the factory, the coupling has been corrected, please do not loosen.
  2. Regularly clean the iron impurities on the permanent magnet plate of the permanent magnet cylinder and the crusherfeeder.
  3. Regularly check the fineness of the finished product.
  4. Cleaning or replacing the duster bag (make sure the bag is breathable), and check the working condition of the solenoid valve regularly (see if it can work normally).
  5. Checking the wear of the wearing parts of the crusher to see if it is normal wear and tear.
  6. Always pay attention to the vibration of the crusher.
  7. If abnormal vibrations such as high vibration and high noise of the crusherare found, stop and then inspection immediately.

fertilizer crushing machine

Correctly Use The Cage Mill

  1. When the hammer of the crusheris severely worn and needs to replace. It is necessary to pay attention to ensure the weight difference between the two hammers on the two opposite (180° direction) hammer pin shafts ≤ 1g and two relatives (180° direction) The total weight difference of the hammer on the hammer pin shaft is ≤ 2g.
  2. When the crusher screen seriously woreand needs to  It is necessary to pay attention to whether the flatness of the new screen and the size of the screen are reasonable, and whether the installation is in place. It is better to make the screen surface face inward when installing.
  3. The opening degree of the impeller feeder damper should adjust
  4. The spindle bearing should add 80 grams of grease after 40 hours of operation, but it can only addto 60%. After 1800 hours of operation, the bearing box cover should remove and all used grease should replace. When replacing the grease, add grease to the area around the roller and the bearing ring, and add 1/3 to 1/2 of the grease to the bottom case. Never add too much grease.
  5. When the output of the crushersuddenly dropped, in addition to the factors of raw materials. It is important to check whether the damper is in place, whether the pipeline is leaking, whether the pulse bag blocked, whether the solenoid valve,  the fan is working normally, and so on.

The mechanical equipment of Fusmar sells well in domestic and foreign markets and enjoys a high welcome among consumers. With years of hard work, Zhengzhou Fusmar has established a complete and effective service system and built an experienced service team. We will carry out after-sales tracking service for the fertilizer crusher equipment sold.

Get In Touch With Us, Our Sales Engineer Will Contact You ASAP!